Molecular Flow Module

Model Low-Pressure Gas Flow in Vacuum Systems with the Molecular Flow Module

 Read more below 

Want to know more?

Understanding and Predicting Free Molecular Flows

Vacuum engineers and scientists use the Molecular Flow Module to design vacuum systems and to understand and predict low-pressure gas flows. The use of simulation tools in the design cycle has become more widespread as these tools improve understanding, reduce prototyping costs, and speed up development. Vacuum systems are usually expensive to prototype. Therefore, an increased use of simulation in the design process can result in substantial cost savings. The gas flows that occur inside vacuum systems are described by different physics than conventional fluid flow problems. At low pressures, the mean free path of the gas molecules becomes comparable to the size of the system and gas rarefaction becomes important. Flow regimes are categorised quantitatively via the Knudsen number (Kn), which represents the ratio of the molecular mean free path to the flow geometry size for gases:

Flow Type
Continuum flow
Slip flow
Transitional flow
Free molecular flow
Knudsen Number
Kn < 0.01
0.01 < Kn < 0.1
0.1 < Kn < 10
Kn > 10

While the Microfluidics Module is used for modelling slip and continuum flows, the Molecular Flow Module is designed for accurately simulating flows in the free molecular flow regime. Historically, flows in this regime have been modelled by the direct simulation Monte Carlo (DSMC) method. This computes the trajectories of large numbers of randomised particles through the system, but introduces statistical noise into the modelling process. For low-velocity flows, such as those encountered in vacuum systems, the noise introduced by DSMC renders the simulations unfeasible.

Accurate Modelling of Low-Pressure, Low-Velocity Gas Flows

The Molecular Flow Module is designed to offer previously unavailable simulation capabilities for the accurate modelling of low-pressure gas flows in complex geometries. It is ideal for the simulation of vacuum systems, including those used in semiconductor processing, particle accelerators, and mass spectrometers. Small channel applications (e.g., shale gas exploration and flow in nanoporous materials) may also be addressed. The Molecular Flow Module uses the angular coefficient method to simulate steady-state free molecular flows, allowing the molecular flux, pressure, number density, and heat flux to be computed on surfaces. The number density can be reconstructed on domains, surfaces, edges, and points from the molecular flux on the surrounding surfaces. You can model isothermal and nonisothermal molecular flows and calculate the heat flux contribution from the gas molecules.

In an ion implanter, the average number density of outgassing molecules along the beam path is used as a figure of merit to evaluate the design. It must be computed as a function of wafer angle, with rotation about one axis.

Product Features

  • Isothermal and nonisothermal flows using the angular coefficient method
  • Reconstruction of number densities on domains, boundaries, edges, and points
  • Multiple species
  • Diffuse flux, evaporation, and reservoir conditions for inflow boundaries
  • Total vacuum and vacuum pump conditions for outflow boundaries
  • Outgassing, thermal desorption, adsorption, and deposition conditions for walls
  • Additional temperature boundary conditions for nonisothermal flows
  • Mesh either the entire geometry or only the surfaces

Application Areas

  • Vacuum systems
  • Semiconductor processing equipment
  • Materials processing equipment
  • Ultra-high vacuum chemical vapor deposition (UHV/CVD)
  • Ion implantation
  • Charge exchange cells
  • Thermal evaporation

 

Every business and every simulation need is different.

In order to fully evaluate whether or not the COMSOL Multiphysics® software will meet your requirements, you need to contact us. By talking to one of our sales representatives, you will get personalised recommendations and fully documented examples to help you get the most out of your evaluation and guide you to choose the best license option to suit your needs.

Fill in your contact details and any specific comments or questions, and submit. You will receive a response from a sales representative within one business day.

Request a Software Demonstration:

Want to know more?

(COMSOL®, COMSOL Multiphysics®, Capture the Concept, COMSOL Desktop®) are registered trademarks of COMSOL AB, LiveLink™ is an unregistered trademark of COMSOL AB, ACIS and SAT are registered trademarks of Spatial Corporation. AutoCAD, AutoCAD Inventor and Inventor are registered trademarks or trademarks of Autodesk, Inc., and/or its subsidiaries and/or affiliates in the USA and/or other countries. CATIA is a registered trademark of Dassault Systèmes or its subsidiaries in the US and/or other countries. Microsoft, Excel and Windows are registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. Parasolid and Solid Edge are trademarks or registered trademarks of Siemens Product Lifecycle Management Software Inc. or its subsidiaries in the United States and in other countries. SolidWorks is a registered trademark of Dassault Systèmes SolidWorks Corporation. Creo and Pro/ENGINEER are trademarks or registered trademarks of PTC Inc. or its subsidiaries in the U.S. and in other countries. MATLAB is a registered trademark of The MathWorks, Inc. Amazon Web Services, the “Powered by Amazon Web Services” logo, Amazon EC2 and Amazon Elastic Compute Cloud are trademarks of Amazon.com, Inc. or its affiliates in the United States and/or other countries. Mac and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries. Linux is a registered trademark of Linus Torvalds. Red Hat is a registered trademark of Red Hat, Inc. in the U.S. and other countries. Neither COMSOL nor any COMSOL products are affiliated with, endorsed by, sponsored by, or supported by any of these other trademark owners. Other product names, brand names or logos are trademarks or registered trademarks of their respective holders.
chevron-left-circlechevron-right-circle